Handtools for Trail Work

Tools for Grubbing

Pulaskis

The Pulaski combines an ax and a grub hoe into one multipurpose firefighting tool. Pulaskis adapt easily to trail work, especially for crews limited to a few tools, or crews with only a general idea of the job to be done. Combination tools are less effective than single purpose tools. An ax balances better and chops more safely and grub hoes are more efficient than Pulaskis. Pulaskis weigh about 5½ pounds. Most have a 36-inch handle.

When using the hoe, stand bent at the waist with your back straight and parallel to the ground, knees flexed, and one foot slightly forward. Hold the handle with both hands so the head is at an angle to your body, and use short, smooth, shallow swings. Let the hoe hit the ground on its corner. Use the ax end to chop large roots after the dirt has been cleared by the hoe. Always wear safety goggles while grubbing to guard against flying chips of rock and dirt.

Use short strokes and let the hoe hit the ground on its corner.

Carry the Pulaski at your side. Grip the handle firmly near the head and point the ax end away from your body and down. Sharpen the cutting edge like an ax. When sharpening the hoe, maintain the existing inside edge bevel. Never sharpen the top of the hoe.

Combi Tools

The combination or combi tool is basically a military entrenching tool on a long handle. It functions as a hoe, pick, or shovel. These tools have recently been developed to aid Forest Service firefighting crews. Because of their wide blade and longer handle, most users have found them less fatiguing to use than traditional tools.

Use, carry, and maintain the tool as you would a Pulaski or McLeod.

Combination (or Combi) tool developed for
firefighting, is popular for trail work.

The combi tool serves as a
hoe, pick, or shovel.

McLeods

The McLeod combines a heavy-duty rake with a large, sturdy hoe. McLeods work well for constructing trails through light soils and vegetation or for reestablishing tread along sloughed side cuts. They are inefficient in rocky or unusually brushy areas. The hoe edge is about 9¾ inches wide, the six rake teeth are 3½ inches long, and the handle is 48 inches long. Weight is about 5 pounds.

Carry McLeods like shovels with the head forward and the handle behind. Grip the handle firmly near the head and hold it away from your body while you walk. Sharpen the hoe with a mill bastard file. Maintain a 45° outside edge bevel. Honing the edge with a whetstone is unnecessary. Rake tines sometimes bend and should be straightened, but they are not sharpened.

Picks

Pick heads have a pointed tip for breaking hard rock by forcing a natural seam. They also have a chisel tip for breaking softer materials. Picks commonly weigh 5 to 10 pounds and most have 36-inch handles.

When using a pick, stand comfortably with your feet about shoulder-width apart and one foot slightly forward. Grasp the handle with your forward hand near the head; place the other hand near the handle end. Bending over at the waist and keeping your back straight and parallel to the ground, work the pick like a Pulaski hoe with short, deliberate, downward strokes. Avoid raising the pick overhead while swinging; this wastes energy and creates a safety hazard because the heavy, narrow tool head cannot be easily controlled or directed. Always wear safety goggles while picking to guard against flying chips of rock.

An oval-tapered eye and handle end cause pick heads to tighten when swung, but allow a worker to remove handles for carrying and sharpening. Sometimes a small screw is screwed into the handle just below the head to prevent slipping. Before sharpening, secure the tool head to free both hands. Use a grinder or mill bastard file to sharpen pointed tips to 1/8-inch square. When sharpening chisel tips, maintain the factory bevel.

Secure the head to the frame by placing a bolt through
the eye of the head and fastening it with a wing nut. This allows
for easy removal and keeps both hands free for sharpening.