Rehabilitation of Asphalt Concrete Pavements: Initial Evaluation of The SPS-5 Experiment-Final Report

Appendix B. Construction Data Summary

Appendix B contains a summary of the construction data available for each project as of the approximate time of this report, which was 1999-2000. Thickness data were from three sources. The first source was the TST_L05B table, which contained the values most representative of the material that was actually placed on the test section and the pre-existing pavement structure. The second was the SPS5_LAYER table, which included thicknesses that should be the same as those provided in the TST_L05B table. However, in most of the data shown, these thicknesses were not the same. The third source was the SPS5_LAYER_ THICKNESS table. These data were obtained from elevation measurements taken on the projects after the placement of each layer of overlay.

Table 95. Summary of construction data for Alabama.
Alabama (1)	501	502	503	504	505	506	507	508	509	563	564
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)
MILLING (mm)
SPS Construction Thickness
AC OVERLAY (mm)		33	102	112	36	76	142	145	81	36	28
Rod & Level
AC OVERLAY (mm)		33	100	110	35	52	123	114	45		30
MILLING (mm)						25	18	29	35	36
Rod & Level Std Dev
AC OVERLAY (mm)		8	9	10	9	6	7	4	5		7
MILLING (mm)						7	7	5	8	6
Rod & Level Min
AC OVERLAY (mm)		18	84	89	18	41	104	104	33		15
MILLING (mm)						10	3	20	18	18
Rod & Level Max
AC OVERLAY (mm)		51	127	137	56	64	137	122	58		51
MILLING (mm)						43	30	41	56	48
MILLING (mm)						42	32	23	25	33	30
Lift Thicknessess
Maximum Lift Thickness<=75mm		41	64	76	43	64	89	79	56	46	38
AC Material Requirements
Hveem stability (minimum 37)Air Voids 3-5 %		3.9	4.2	3.6	3.6	3.6	3.6	4.2	4.2	3.6	3.9
Virgin Mix
Aggregate Pass #4<40%
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 96. Summary of construction data for Arizona.
Arizona (4)	501	502	503	504	505	506	507	508	509	559	560
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		69	119	122	71	132	173	165	99	152	56
MILLING (mm)		23	20	18	23	48	66	69	71	86	23
SPS Construction Thickness
AC OVERLAY (mm)		69	119	122	71	43	104	104	38	76	56
Rod & Level
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Std Dev
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Min
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Max
AC OVERLAY (mm)
MILLING (mm)
MILLING (mm)		27	18	27	33	72	69	69	64	99	25
Lift Thicknessess
Maximum Lift Thickness<=75mm		64	76	74	74	74	81	76	71	109	66
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%		64			57
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%		53	53						53	53	53

Note: The number after the state name is the state’s numeric code in the LTPP date base.

Table 97. Summary of construction data for California.
California (6)	501	502	503	504	505	506	507	508	509	559	560	561	562	563	564	565	566	567	568	569	570	571
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)	46	76	166	146	91	109	170	168	112	208	109	107	112	102	109	109	109	102	152	183	183	248
MILLING (mm)		30	38	36	30	43	48	46	51	76	58	58	58	58	66	58	58	58	58	66	91	91
SPS Construction Thickness
AC OVERLAY (mm)	46	76	166	145	91	109	170	114	112	152	109	107	107	102	102	109	109	102	152	183	183	244
Rod & Level
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Std Dev
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Min
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Max
AC OVERLAY (mm)
MILLING (mm)
MILLING (mm)
Lift Thicknessess
Maximum Lift Thickness<=75mm	64	69	107	102	71	81	69	74	71	122	0	71	71	81	89	74	76	71	157	53	51	48
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%	48	48	48					48

Note: The number after the state name is the state’s numeric code in the LTPP date base.

Table 98. Summary of construction data for Colorado.
Colorado(8)	501	502	503	504	505	506	507	508	509	559	560
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)	33	97	137	147	81	112	173	201	107	168	155
MILLING (mm)	0	0	0	0	0	51	51	71	51	0	0
SPS Construction Thickness
AC OVERLAY (mm)	33	97	145	147	81	94	175	201	109	175	157
Rod & Level
AC OVERLAY (mm)		89	135	154	74	65	149	132	65	172	151
MILLING (mm)
Rod & Level Std Dev
AC OVERLAY (mm)		13	18	17	21	28	19	25	16	30	20
MILLING (mm)
Rod & Level Min
AC OVERLAY (mm)		66	97	94	0	0	97	0	20	76	117
MILLING (mm)
Rod & Level Max
AC OVERLAY (mm)		112	196	180	109	102	188	168	97	234	196
MILLING (mm)
MILLING (mm)						52	52	55	52
Lift Thicknessess
Maximum Lift Thickness<=75mm	30	79	89	107	74	64	71	84	64	114	64
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%							60		62
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%		58	58					58	58

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 99. Summary of construction data for Florida.
Florida (12)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		64	127	130	51	76	165	178	107
MILLING (mm)		38				36			64
SPS Construction Thickness
AC OVERLAY (mm)		53	135	122	48	102	168	180	107
Rod & Level
AC OVERLAY (mm)		50	134	123	50	65	111	113	65
MILLING (mm)	.	.	.	.		35	55	67	42
Rod & Level Std Dev
AC OVERLAY (mm)		9	7	8	4	4	6	7	5
MILLING (mm)	.	.	.	.		6	5	4	10
Rod & Level Min
AC OVERLAY (mm)		25	112	102	38	58	102	94	53
MILLING (mm)	.	.	.	.		20	46	61	20
Rod & Level Max
AC OVERLAY (mm)		61	150	145	58	74	122	124	71
MILLING (mm)	.	.	.	.		43	66	76	71
MILLING (mm)		22		11	25	69	62	70	72
Lift Thicknessess
Maximum Lift Thickness =75mm		38	69	58	38	81	76	84	53
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%					79		60		69
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%		72	62					62	72

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 100. Summary of construction data for Georgia.
Georgia (13)	501	502	503	504	505	506	507	508	509	560	561	562	563	564	565	566
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		41	130	135	51	107	160	170	97	56	74	89	56	58	127	137
MILLING (mm)		30	38	41	46	74	53	53	58	30	20	25	76	58	25	56
SPS Construction Thickness
AC OVERLAY (mm)		23	127	130	41	99	168	175	99
Rod & Level
AC OVERLAY (mm)		23	125	128	42	48	119	123	43
MILLING (mm)
Rod & Level Std Dev
AC OVERLAY (mm)		8	4	7	9	4	15	5	6
MILLING (mm)	.	.	.	.		52	47	49	57
Rod & Level Min
AC OVERLAY (mm)		5	119	119	33	43	109	109	30
MILLING (mm)	.	.	.	.		7	12	3	6
Rod & Level Max
AC OVERLAY (mm)		36	132	142	81	58	185	132	51
MILLING (mm)	.	.	.	.		41	0	41	48
MILLING (mm)			18	27	30	61	38	65	41
Lift Thicknessess
Maximum Lift Thickness =75mm		28	64	58	46	64	114	114	71
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%							64		66
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 101. Summary of construction data for Maine.
Maine(23)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		91	140	145	69	104	198	173	97
MILLING (mm)						38	43	30	38
SPS Construction Thickness
AC OVERLAY (mm)		86	142	142	61	102	183	175	94
Rod & Level
AC OVERLAY (mm)		91	140	144	69	54	133	121	52
MILLING (mm)	.	.	.	.		50	57	52	43
Rod & Level Std Dev
AC OVERLAY (mm)		9	9	10	9	6	6	6	5
MILLING (mm)	.	.	.	.		7	7	5	6
Rod & Level Min
AC OVERLAY (mm)		76	122	122	51	41	122	107	36
MILLING (mm)	.	.	.	.		30	46	41	30
Rod & Level Max
AC OVERLAY (mm)		114	155	165	84	66	145	140	66
MILLING (mm)	.	.	.	.		66	76	61	56
MILLING (mm)						43	47	37	38
Lift Thicknessess
Maximum Lift Thickness<=75mm		61	58	58	38	58	89	81	58
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%			45	52		46	52	48	44
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%		47	39					39	39

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 102. Summary of construction data for Maryland.
Maryland(24)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		53	135	135	53	91	191	168	97
MILLING (mm)						38	36	36	38
SPS Construction Thickness
AC OVERLAY (mm)		53	124	114	51	91	188	140	89
Rod & Level
AC OVERLAY (mm)		46	124	116	48	55	108	139	45
MILLING (mm)							45		44
Rod & Level Std Dev
AC OVERLAY (mm)		7	8	9	6	5	6	6	4
MILLING (mm)							9		8
Rod & Level Min
AC OVERLAY (mm)		28	109	97	36	46	97	127	33
MILLING (mm)							33		25
Rod & Level Max
AC OVERLAY (mm)		58	140	140	64	66	124	150	51
MILLING (mm)							71		64
MILLING (mm)						39	39	39	39
Lift Thicknessess
Maximum Lift Thickness<=75mm		61	61	66	64	64	64	57	64
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%				41	49
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 103. Summary of construction data for Minnesota.
Minnesota (27)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		61			48		142
MILLING (mm)
SPS Construction Thickness
AC OVERLAY (mm)
Rod & Level
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Std Dev
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Min
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Max
AC OVERLAY (mm)
MILLING (mm)
MILLING (mm)
Lift Thicknessess
Maximum Lift Thickness<=75mm
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 104. Summary of construction data for Mississippi.
Mississippi(28)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		51	117	124	51
MILLING (mm)		0	0	0	0
SPS Construction Thickness
AC OVERLAY (mm)		51	127	127	51	80	165	165	89
Rod & Level
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
Rod & Level Std Dev
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
Rod & Level Min
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
Rod & Level Max
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
MILLING (mm)						38	38	38	38
Lift Thicknessess
Maximum Lift Thickness<=75mm		56	51	51	51	51	51	51	51
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%
RAP
TOTAL AC
NEW AC		4	4					4	4
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL		70	70					70	70
% RAP
New Aggregate
Aggregate Pass #4 <40%		67	67					67	67

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Tab1e 105. Summary of construction data for Missouri.
Missouri(29)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)
MILLING (mm)
SPS Construction Thickness
AC OVERLAY (mm)
Rod & Level
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Std Dev
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Min
AC OVERLAY (mm)
MILLING (mm)
Rod & Level Max
AC OVERLAY (mm)
MILLING (mm)
MILLING (mm)
Lift Thicknessess
Maximum Lift Thickness<=75mm
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 106. Summary of construction data for Montana.
Montana (30)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		66	117	142	51	107	183	180	114
MILLING (mm)		20	28	33	15	69	71	71	66
SPS Construction Thickness
AC OVERLAY (mm)		66	117	142	51	107	191	180	114
Rod & Level
AC OVERLAY (mm)		27	101	92	37	28	95	89	28
MILL REPLACEMENT (mm)
Rod & Level Std Dev
AC OVERLAY (mm)		8	10	10	9	9	9	11	8
MILL REPLACEMENT (mm)
Rod & Level Min
AC OVERLAY (mm)		10	79	74	13	13	74	51	13
MILL REPLACEMENT (mm)
Rod & Level Max
AC OVERLAY (mm)		46	119	127	64	48	122	117	46
MILL REPLACEMENT (mm)
MILLING (mm)		25	25	25	25	79	77	77	76
Lift Thicknessess
Maximum Lift Thickness<=75mm		61	94	89	64	74	94	94	71
AC Material Requirements
Hveem stability (minimum 37)Air Voids 3-5 %
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%		51			55
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%		51	51					51	51

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 107. Summary of construction data for New Jersey.
New JerseY (34)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		48	119	119	46	107	198	198	109
MILLING (mm)		0	0	0	0	51	51	51	51
SPS Construction Thickness
AC OVERLAY (mm)		51	127	127	127	102	178	178	102
Rod & Level
AC OVERLAY (mm)		43	114	118	53	49	56	123	41
MILL REPLACEMENT (mm)						54	56	55	64
Rod & Level Std Dev
AC OVERLAY (mm)		12	9	8	9	6	6	14	6
MILL REPLACEMENT (mm)						9	10	8	11
Rod & Level Min
AC OVERLAY (mm)		18	99	102	28	28	43	81	23
MILL REPLACEMENT (mm)						28	36	36	48
Rod & Level Max
AC OVERLAY (mm)		69	132	137	76	61	66	156	51
MILL REPLACEMENT (mm)						69	89	86	99
MILLING (mm)						74	53	58	64
Lift Thicknessess
Maximum Lift Thickness<=75mm		61	89	102	64	76	97	102	76
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%			53	55			61	52
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL
% RAP
New Aggregate
Aggregate Pass #4 <40%

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 108. Summary of construction data for New Mexico.
New Mexico(35)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)
MILLING (mm)
SPS Construction Thickness
AC OVERLAY (mm)		56	107	117	64	109	188	188	107
Rod & Level
AC OVERLAY (mm)	48	56	107	117	63	55	133	132	53
MILL REPLACEMENT (mm)						54	56	56	53
Rod & Level Std Dev
AC OVERLAY (mm)	6	12	11	11	9	4	5	6	6
MILL REPLACEMENT (mm)						4	5	5	6
Rod & Level Min
AC OVERLAY (mm)	33	33	86	91	48	48	122	122	33
MILL REPLACEMENT (mm)						46	46	46	33
Rod & Level Max
AC OVERLAY (mm)	61	79	127	137	79	66	145	147	64
MILL REPLACEMENT (mm)						66	66	69	64
MILLING (mm)	51					51	51	64	51
Lift Thicknessess
Maximum Lift Thickness<=75mm	76	76	102	76	64	76	76	76	76
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%			49		59		59	59
RAP
TOTAL AC
NEW AC		5	5					5	5
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL		45	45					45	45
% RAP
New Aggregate
Aggregate Pass #4 <40%		43	43					43	43

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 109. Summary of construction data for Oklahoma.
Oklahoma (40)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)
MILLING (mm)
SPS Construction Thickness
AC OVERLAY (mm)		46	112	119	43	99	163	147	79
Rod & Level
AC OVERLAY (mm)		46	112	119	43	99	163	146	78
MILL REPLACEMENT (mm)
Rod & Level Std Dev
AC OVERLAY (mm)		8	13	13	7	13	11	13	9
MILL REPLACEMENT (mm)
Rod & Level Min
AC OVERLAY (mm)		25	79	79	20	74	145	124	56
MILL REPLACEMENT (mm)
Rod & Level Max
AC OVERLAY (mm)		64	140	142	56	124	188	170	97
MILL REPLACEMENT (mm)						41	30	36	43
MILLING (mm)
Lift Thicknessess
Maximum Lift Thickness<=75mm		64	89	89	64	102	102	102	102
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%			42	47			42	34
RAP
TOTAL AC
NEW AC
% AC OF SALVAGED MIX		1	1					1	1
% NEW AGG.MATERIAL		70	70					70	70
% RAP
New Aggregate
Aggregate Pass #4 <40%		59	59					59	59

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 110. Summary of construction data for Texas.
Texas(48)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		56	135	135	51	99	178	185	109
MILLING (mm)		0	0	0	0
SPS Construction Thickness
AC OVERLAY (mm)		58	124	124	97	114	175	168	102
Rod & Level
AC OVERLAY (mm)		58	123	122	59	59	120	116	54
MILL REPLACEMENT (mm)						56	55	53	47
Rod & Level Std Dev
AC OVERLAY (mm)		8	19	9	10	7	7	7	11
MILL REPLACEMENT (mm)						7	6	6	5
Rod & Level Min
AC OVERLAY (mm)		43	0	102	30	46	99	102	0
MILL REPLACEMENT (mm)						41	38	43	33
Rod & Level Max
AC OVERLAY (mm)		74	145	145	79	76	135	127	71
MILL REPLACEMENT (mm)						71	76	64	66
MILLING (mm)						44	46	37	43
Lift Thicknessess
Maximum Lift Thickness<=75mm		58	53	48	58	58	56	48	53
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%							55		55
RAP
TOTAL AC
NEW AC		3	3					3	3
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL		65	65					65	65
% RAP
New Aggregate
Aggregate Pass #4 <40%		71	71					71	71

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 111. Summary of construction data for Alberta.
Alberta (81)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		53	127	122		94	163	178	84
MILLING (mm)		0		0	0	41	56	76	64
SPS Construction Thickness
AC OVERLAY (mm)		53	127	122	53	94	160	178	84
Rod & Level
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
Rod & Level Std Dev
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
Rod & Level Min
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
Rod & Level Max
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
MILLING (mm)						56	53	48	50
Lift Thicknessess
Maximum Lift Thickness<=75mm		58	74	76	58	61	71	74	61
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %
Virgin Mix
Aggregate Pass #4<40%				64				64
RAP
TOTAL AC
NEW AC		4	4					4	4
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL		70	70					70	70
% RAP
New Aggregate
Aggregate Pass #4 <40%		64	64					64	64

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Table 112. Summary of construction data for Manitoba.
Alberta (81)	501	502	503	504	505	506	507	508	509
Required Thickness
AC OVERLAY (mm)	0	51	127	127	51	51	127	127	51
MILLING (mm)	0	<25.4	<25.4	<25.4	<25.4	38–50	38–50	38–50	38–50
L05B Thickness
AC OVERLAY (mm)		69	124	142		81	165	165	94
MILLING (mm)					0
SPS Construction Thickness
AC OVERLAY (mm)		64	140	127	51	89	165	165	89
Rod & Level
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
Rod & Level Std Dev
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
Rod & Level Min
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
Rod & Level Max
AC OVERLAY (mm)
MILL REPLACEMENT (mm)
MILLING (mm)						38	38	38	38
Lift Thicknessess
Maximum Lift Thickness<=75mm		51	51	51	51	51	38	38	51
AC Material Requirements
Hveem stability (minimum 37)
Air Voids 3-5 %		4.5	4.5	3.9	3.9	3.9	3.9	4.5	4.5
Virgin Mix
Aggregate Pass #4<40%
RAP
TOTAL AC
NEW AC		5	5					5	5
% AC OF SALVAGED MIX
% NEW AGG.MATERIAL		70	70					70	70
% RAP
New Aggregate
Aggregate Pass #4 <40%		62	62					62	62

Note: The number after the state name is the state’s numeric code in the LTPP data base.

Research Home \| Pavements Home

This report is an archived publication and may contain dated technical, contact, and link information